 |
 |
PRODUCT OUTLINE
Each DataDot kit contains 1,000 dots laser etched with
a unique PIN number for each vehicle.
The dots are
pre-mixed in a water based adhesive and come with a
fitment brush, two window decals, an engine decal and
two bar code labels (one for the vehicle and the other
for dealer paperwork). The entire kit is supplied in a
pre-marked box with a separate box provided for each
vehicle.
VEHICLE PREPARATION
The DataDots take on average 3 - 4 minutes to apply.
The surface upon which the dots are to be applied should
be dry, clean and free of oil, grease, wax, and other
deposits. If not please wipe surface with Prepsol or
Triclean. There is no need to move or get underneath
the vehicle.
APPLICATION GUIDELINE
- Please read safety and warning information prior to use.
- Place the DataDot PIN bar code along with the Vehicle Identification Number of the vehicle on the work sheet. Place second bar code sticker on end of driver side door of post.
- Shake container for 10 - 20 seconds before removing cap and seal.
- If contents are spilt or contaminated, record number as damaged and replace with new DataDot PIN code. Do not mix dot kits between vehicles.
- Apply to vehicle surfaces as per template provided.
- Care should be taken to apply enough adhesive to cover the dots.
- When completed, ensure that bottle and brush are disposed in a manner that avoids theft, possible reuse or general pollution.
- Please do not apply adhesive or dots on the surface paint of the vehicle, in air conditioning ducts, face of alloy wheels or any other cosmetic part of the vehicle. If done so, quickly wipe and clean with a damp cloth within 5 minutes.
DRYING TIMES
- Touch dry in 10 to 20 minutes (may be longer with inclement weather)
- Vehicle can be driven immediately
- Adhesive fully cures in 24 hours (based on weather conditions)
|
 |
|
- Complete Registration Form - Recording DataDot Number and Vehicle Identification Number (VIN)
- Ensure area to be marked is clean and free of residues before application of DataDots
- Secure DataDot engine compartment sticker and apply 3-4 dots in the square
- Shake container well, remove seal, stir with brush
- Apply DataDots as per the template provided
- Place DataDot warning sticker on the inside of passenger's and driver's windows
|
PRODUCT SAFETY WARNING - Please Read Before Use
CAUTION
Dry material may adhere strongly to
skin and eyes. Wash effected areas
with large amounts of water before
product dries.
FIRST AID
- Eyes - flush with water before product
dries continuously for 5 to 15 minutes.
- Skin - remove with warm, soapy water.
Product is not harmful, but may cause
irritation in some individuals.
If irritation develops, see a physician.
Inhalation is not expected to be a factor
but if problems occur, remove to fresh air.
For Ingestion dilute by immediately drinking
2 to 3 glasses of water.
DO NOT INDUCE VOMITING.
Seek medical assistance if discomfort
persists.
HANDLING AND STORAGE
Do not freeze. Once product is
frozen, it may be spoiled.
Store between 5 C (40 F) and
35 C (95 F). Keep container
sealed when not in use.
| Flammability: |
0 |
|
Health Hazard: |
1 |
| Reactivity: |
0 |
Specific Hazard: |
None |
See the MSDS for more information. |
|
|
|
|
 |
MIGHTYDOT ID LABEL
Please place this label on a clean metal painted surface in front of the engine compartment.
|
|
ENGINE COMPARTMENT LABEL
Place 3 to 4 DataDots in the empty square on the engine compartment label.
|
|
DOORS AND HINGES
Place DataDots under each door and around each hinge. Same applies for sliding doors.
|
|
REGISTRATION STICKER
Usually at end of driver door or on post. Brush DataDots on both sticker and painted area. This assures sticker has not been tampered with.
|
MIGHTYDOT WARNING DECAL
Place decal on inside of driver and passenger window.
|
|
INSIDE REINFORCING OPENINGS
Four corners and Hinge Areas
|
|
| OPTIONAL MIGHTYDOT APPLICATION POINTS |
- Electric Radiator Fans
- Under Seats
- Turbo Charger
- Inside Front and Rear Bumpers
- Spare Tire
|
|
- Inside Alloy Wheels
- Spare Wheel Well
- Back of Tail Lights
- Intercooler
|
|
|
|
|
 |
ENGINE COVER
Many engine covers can be easily removed, if so, please remove to brush-on dots, if cover is not easily removed, then brush-on dots in and around engine area as best as possible.
|
|
ENGINE MARKINGS
|
- Strut Housings
- Air Intake Housing
- Throttle Positioner
- ABS Module
- Engine Block
(Brush in many locations)
- Computer Housing
- Fuse Box
- Transmission Housing
- Speed Control
- Headlight Housing
- Intake Manifold
- Radiator
- Alternator and Air Compressor
|
|
|
|
|
